коды ошибки харлей дэвидсон
moto strangers
03-07 HD DTC Codes and Activation
The IM (instrument module) is capable of displaying DTC’s (diagnostic trouble codes).
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC).
1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
2- Push odometer reset button in & hold.
3- Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.
4 — Push the odometer reset button once and you will see the selection menu «PSSPt» with the first P flashing.
5 — Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carbureted)
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
SP = speedometer
T = tachometer
6 — To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer reset button again to view additional codes if they exist.
7 — Record the codes.
8 — If DTC’s are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear.
9 – Press and release the odometer reset button to continue to the next module.
10 – Turn Ignition switch to OFF.
On models not equipped with a tachometer «No Rsp» will appear when the tachometer identifier is selected.
«No Rsp» will also appear if the run/off switch is in the off position when doing this procedure.
Also if the code set is a historic code (not a constant light) after 50 start and run cycles of at least 30 seconds each in duration, the light will extinguish itself as long as the error hasn’t occurred again.
If it were a current code, the light would remain lit while running.
DTC FAULT CONDITION MODULE
«BUS Er» Serial data bus shorted/low/open/high
B0563 Battery Voltage High TSM/TSSM
B1004 Fuel Level Sending Unit Low Instruments
B1005 Fuel Level Sending Unit High/Open Instruments
B1006 Accessory Line Over voltage Instruments
B1007 Ignition Line Over voltage Instruments
B1008 Reset Switch Closed Instruments
B1122 Right turn output fault
B1131 Alarm Output Low TSM/TSSM
B1132 Alarm Output High TSM/TSSM
B1134 Starter Output High TSM/TSSM
B1135 Accelerometer Fault TSM/TSSM
B1141 Ignition switch open/low
B1151 Sidecar BAS Low TSM/TSSM
B1152 Sidecar BAS High TSM/TSSM
B1153 Sidecar BAS Out of Range TSM/TSSM
P0106 MAP Sensor Rate of Range Error Carb
P0107 Map Sensor Failed Open/Low Carb
P0107 Map Sensor Open/Low EFI
P0108 Map Sensor Failed High Carb
P0108 Map Sensor High EFI
P0112 IAT Sensor Voltage Low EFI
P0113 IAT Sensor Voltage Open/High EFI
P0117 ET Sensor Voltage Low EFI
P0118 ET Sensor Voltage Open/High EFI
P0122 TP Sensor Open/Low EFI
P0123 TP Sensor High EFI
P0131 Front 02 sensor low (lean)
P0132 Engine running rich
P0134 Front 02 sensor open/not responding
P0151 Rear 02 sensor low (lean)
P0152 Rear 02 sensor high (rich)
P0154 Rear 02 sensor open/not responding
P0261 Front Injector Open/Low EFI
P0262 Front Injector High EFI
P0263 Rear Injector Open/Low EFI
P0264 Rear Injector High EFI
P0373 CKP Sensor Intermittent Carb
P0373 CKP Sensor Intermittent EFI
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Sync Error EFI
P0501 VSS Low Carb
P0501 VSS Low EFI
P0502 VSS High/Open Carb
P0502 VSS High/Open EFI
P0505 Loss of Idle Sped Control EFI
P0562 Battery Voltage Low Carb
P0562 Battery Voltage Low EFI
P0563 Battery Voltage High Carb
P0563 Battery Voltage High EFI
P0602 Calibration Memory Error Carb
P0603 EEPROM Failure Carb
P0603 ECM EEPROM Error EFI
P0604 RAM Failure Carb
P0605 Program Memory Error Carb
P0605 ECM Flash Error EFI
P0607 Converter Error Carb
P0661 Intake solenoid low/open
P0662 Intake solenoid high/shorted
P1001 System Relay Coil Open/Low EFI
P1002 System relay Coil High/Shorted EFI
P1003 System relay Contacts Open EFI
P1004 System Relay Contacts Closed EFI
P1009 Incorrect Password Carb
P1009 Incorrect Password EFI
P1010 Missing Password Carb
P1010 Missing Password EFI
P1351 Front Ignition Open/Low Carb
P1351 Front Ignition Open/Low EFI
P1352 Front Ignition Coil High/Shorted Carb
P1352 Front Ignition Coil High/Shorted EFI
P1353 Front Cylinder No Combustion EFI
P1354 Rear Ignition Coil Open/Low Carb
P1354 Rear Ignition Coil Open/Low EFI
P1355 Rear Ignition Coil High/Shorted Carb
P1355 Rear Ignition Coil High/Shorted EFI
P1356 Rear Cylinder No Combustion EFI
P1357 Intermittent Secondary Front EFI
P1358 Intermittent Secondary Rear EFI
U1016 Loss of ICM/ECM Serial Data Instruments
U1016 Loss of ECM Serial Data, Vehicle Speed, Vehicle Inhibit Motion or Power train Security Status TSM/TSSM
U1064 Loss of TSM/TSSM Serial Data Carb
U1064 Loss of TSM/TSSM Serial Data EFI
U1064 Loss of TSM/TSSM Serial Data Instruments
U1097 Loss of Speedometer Serial data Carb
U1097 Loss of Speedometer Serial data EFI
U1097 Loss of Speedometer Serial data TSM/TSSM
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
U1300 Serial Data Low Carb
U1300 Serial Data Low EFI
U1300 Serial Data Low Instruments
U1300 Serial Data Low TSM/TSSM
U1301 Serial Data Open/High Carb
U1301 Serial Data Open/High EFI
U1301 Serial Data Open/High Instruments
U1301 Serial Data Open/High TSM/TSSM
2006 models with 02 sensors (Dynas)
P0131 Front 02 sensor lean for any length of time
P0151 Rear 02 sensor lean for any length of time
Above codes can also be set if 02 sensor fails.
AFR – Air Fuel Ratio
ATS – Air Temperature Sensor
BAS – Bank Angle Sensor
CCM – Cruise Control Module
CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed. Home position established by taking readings off the 22 teeth on the alternator rotor.
DTC – Diagnostic Trouble Codes
ECM – Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & TP sensors) and controls the low-voltage circuits for the ignition coils and injectors. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage. The programmed dwell feature gives adequate spark at all speeds.
ECT – Engine Coolant Temperature. Sensor also controls the cooling fan relay that provides 12 Vdc to the fans.
EFI – Electronic Fuel Injection
EFP – Electronic Fuel Pump
ET – Engine Temperature sensor
FI – Fuel Injectors
FPR – Fuel Pressure regulator
IAC – Idle Air Control actuator
IAT – Intake Air Temperature sensor
ISS – Ion Sensing System…detonation detection
MAP – manifold Absolute Pressure sensor. The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. The EMC then adjusts the spark and fuel-timing advance curves for optimum performance.
TP – Throttle Position Sensor
TSM/TSSM (Turn Signal/ Turn Signal Security Module)
VE – Volume Efficiency
VSS – Vehicle Speed Sensor. Used as an input for idle speed control
Добавить комментарий Отменить ответ
Для отправки комментария вам необходимо авторизоваться.
Этот сайт использует Akismet для борьбы со спамом. Узнайте, как обрабатываются ваши данные комментариев.
Коды ошибки харлей дэвидсон
Зажав кнопку ресета одометра и включив зажигание, заходим в диалоговое окно с надписью diag
Нажимая кнопки включения поворотов получаем вход в различные директории самодиагностики
PSCB выбирая кнопками поворотов моргание одной из букв 5ти секундным нажатием можем проверить мотокил на наличие ошибок.
Ниже приведены пояснения по каждой директории
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module
Зажигание и управление инжектором
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
Система сигнализации и управления поворотами
List of all v-rod fault codes
RANKING DTC STATUS FAULT CONDITION SOLUTION
1 P0605 Current ECM flash error 4.29 DTC P0603, P0605
2 P0605 Historic ECM flash error 4.29 DTC P0603, P0605
3 P0603 Current ECM EEPROM error 4.29 DTC P0603, P0605
4 P0603 Historic ECM EEPROM error 4.29 DTC P0603, P0605
5 U1300 Current ECM serial data low 4.12 STARTS, THEN STALLS
6 U1301 Current ECM serial data open/high 4.12 STARTS, THEN STALLS
7 U1300 Current TSSM serial data low 4.12 STARTS, THEN STALLS
8 U1301 Current TSSM serial data open/high 4.12 STARTS, THEN STALLS
9 U1300 Current IM serial data low 4.12 STARTS, THEN STALLS
10 U1301 Current IM serial data open/high 4.12 STARTS, THEN STALLS
11 U1064 Current Loss of TSM/TSSM serial data-at ECM 4.32 DTC U1064, U1255
12 U1016 Current Loss of all ECM serial data-at TSSM 3.19 DTC U1016
13 U1096 Current Loss of IM serial data-at TSSM 3.20 DTC U1096, U1255
14 U1255 Current Missing response-at TSSM 4.32 DTC U1064, U1255
15 U1064 Current Loss of TSM/TSSM serial data-at IM 2.15 DTC U1064, U1255
16 U1016 Current Loss of all ECM serial data-at IM 2.14 DTC U1016
17 U1255 Current Missing response-at IM
4.33 DTC U1096, U1255
18 P1003 Current System relay contacts open 4.14 SYSTEM RELAY CHECK
19 P1002 Current System relay coil high/shorted 4.14 SYSTEM RELAY CHECK
20 P1001 Current System relay coil open/low 4.14 SYSTEM RELAY CHECK
21 P1004 Current System relay contacts closed 4.14 SYSTEM RELAY CHECK
22 P1009 Current Incorrect password 4.30 DTC P1 009, P1010
23 P1010 Current Missing password 4.30 DTC P1 009, P1010
24 P0373 Current CKP sensor intermittent 4.25 DTC P0373, P0374
25 P0374 Current CKP sensor synch error 4.25 DTC P0373, P0374
26 P0122 Current TP sensor open/low 4.23 DTC P0122, P0123
27 P0123 Current TP sensor high 4.23 DTC P01 22, P0123
28 P0107 Current MAP sensor open/low 4.20 DTC P01 07, P0108
29 P0108 Current MAP sensor high 4.20 DTC P01 07, P0108
30 P0117 Current ET sensor voltage low 4.22 DTC P01 17, P0118
31 P0118 Current ET sensor open/high 4.22 DTC P01 17, P0118
32 P0112 Current IAT sensor voltage low 4.21 DTCP0112, P0113
33 P0113 Current IAT sensor open/high 4.21 DTCP0112, P0113
34 P1351 Current Front ignition coil open/low 4.31 DTC P1351, P1352, P1354, P1355
35 P1354 Current Rear ignition coil open/low 4.31 DTC P1351, P1352, P1354, P1355
36 P1352 Current Front ignition coil high/shorted 4.31 DTC P1351, P1352, P1354, P1355
37 P1355 Current Rear ignition coil high/shorted 4.31 DTC P1351, P1352, P1354, P1355
38 P1357 Current Front cylinder combustion intermittent 4.19 COMBUSTION ABSENT/INTERMITTENT
39 P1358 Current Rear cylinder combustion intermittent 4.19 COMBUSTION ABSENT/INTERMITTENT
42 P0262 Current Front injector high 4.24 DTC P0261, P0262, P0263, P0264
44 P0562 Current Battery voltage low 4.28 DTC P0562, P0563
45 P0563 Current Battery voltage high 4.28 DTC P0562, P0563
48 P1651 Current Check engine light open/low 4.6 IM SELF DIAGNOSTICS
49 P1652 Current Check engine light high 4.6 IM SELF DIAGNOSTICS
50 P1653 Current Tachometer low 4.6 IM SELF DIAGNOSTICS
51 P1654 Current Tachometer high 4.6 IM SELF DIAGNOSTICS
52 P1356 Current Rear cylinder no combustion 4.19 COMBUSTION ABSENT/INTERMITTENT
53 P1353 Current Front cylinder no combustion 4.19 COMBUSTION ABSENT/INTERMITTENT
54 P0444 Current Purge control open/low 4.26 DTC P0444,
Коды ошибки харлей дэвидсон
Коды ошибок можно проверить сдесь
http://www.1130cc.com/?page=codes
Мотобратве желаю их отсутсвия.
The IM (instrument module) is capable of displaying DTC’s (diagnostic trouble codes).
1- Ignition off
2- push odometer reset button in & hold. Make sure run switch is on.
3- turn ignition to run and release button (you will see P, S &C displayed)
4- each letter represents an area of diagnostics. the one that is flashing is the one you are going to check. To move from one letter to the next, you push the button one time. (from P to S to C and back to P, etc.)
5- to get DTC within an area, you push and hold the button in for 5 seconds and if there are any, it will be displayed. you can release the button. As you push the button again, other codes will appear if they are there. If there are not any the word ‘none’ appears.
6- Record the codes.
7- To determine if a code is current or historic, you clear the codes while being displayed by pushing in and holding the button until ‘clear’ comes up. Turn off the ignition. then crank or restart the bike. turn off, and then repeat the code process. If a code is there now, its current. if not, it was historic.
List of all v-rod fault codes
49 P1652 Current Check engine light high 4.6 IM SELF DIAGNOSTICS
50 P1653 Current Tachometer low 4.6 IM SELF DIAGNOSTICS
51 P1654 Current Tachometer high 4.6 IM SELF DIAGNOSTICS
52 P1356 Current Rear cylinder no combustion 4.19 COMBUSTION ABSENT/INTERMITTENT
53 P1353 Current Front cylinder no combustion 4.19 COMBUSTION ABSENT/INTERMITTENT
54 P0444 Current Purge control open/low 4.26 DTC P0444, P0445
55 P0445 Current Purge control high 4.26 DTC P0444, P0445
56 P1481 Current Fan output open/low 4.15 FAN OPERATION CHECK
57 P1482 Current Fan output high 4.15 FAN OPERATION CHECK
58 P0505 Current Loss of idle speed control 4.17 IDLE AIR CONTROL
59 B1135 Current Accelerometer fault 3.1 8 DTC B1 135
60 B1134 Current Starter output high 3.1 7 DTC B1 134
61 B1121 Current Left turn output fault 3.14 TURN SIGNAL ERRORS
62 B1122 Current Right turn output fault 3.14 TURN SIGNAL ERRORS
63 B0563 Current Battery voltage high 3.15DTCB0563
64 B1131 Current Alarm output low 3.16 DTC B1131.B1132
65 B1132 Current Alarm output high 3.16 DTC B1131.B1132
66 B1141 Current Ignition switch open/low 3.14 TURN SIGNAL ERRORS
67 B1003 Current IM internal fault 2. 10 DTC B1 003
68 B1004 Current Fuel sender low 2.11 DTCB1004/B1005
69 B1005 Current Fuel sender open/high 2.11 DTCB1004/B1005
70 B1006 Current Accessory line overvoltage 2.12DTCB1006/B1007
71 B1007 Current Ignition line overvoltage 2.12DTCB1006/B1007
72 B1008 Current Trip switch closed 2. 13 DTC B1 008
73 U1300 Historic ECM serial data low 4.12 STARTS, THEN STALLS
74 U1301 Historic ECM serial data open/high 4.12 STARTS, THEN STALLS
75 U1300 Historic TSSM serial data low 4.12 STARTS, THEN STALLS
76 U1301 Historic TSSM serial data open/high 4.12 STARTS, THEN STALLS
77 U1300 Historic IM serial data low 4.12 STARTS, THEN STALLS
78 U1301 Historic IM serial data open/high 4.12 STARTS, THEN STALLS
79 U1064 Historic Loss of TSM/TSSM serial data-at ECM 4.32 DTC U1064, U1255
80 U1016 Historic Loss of all ECM serial data-at TSSM 3.19 DTC U1016
81 U1096 Historic Loss of IM serial data-at TSSM 3.20 DTC U 1096, U1255
82 U1255 Historic Missing response-at TSSM 4.32 DTC U1064, U1255
83 U1064 Historic Loss of TSM/TSSM serial data-at IM 2.15 DTC U1064, U1255
84 U1016 Historic Loss of all ECM serial data-at IM 2.14 DTC U1016
85 U1255 Historic Missing response-at IM 4.33 DTC U1 096, U1 255
86 P1003 Historic System relay contacts open 4.14 SYSTEM RELAY CHECK
87 P1002 Historic System relay coil high/shorted 4.14 SYSTEM RELAY CHECK
88 P1001 Historic System relay coil open/low 4.14 SYSTEM RELAY CHECK
89 P1004 Historic System relay contacts closed 4.14 SYSTEM RELAY CHECK
90 P1009 Historic Incorrect password 4.30 DTC P1 009, P1010
91 P1010 Historic Missing password 4.30 DTC P1 009, P1 010
92 P0373 Historic CKP sensor intermittent 4.25 DTC P0373, P0374
93 P0374 Historic CKP sensor synch error 4.25 DTC P0373, P0374
94 P0122 Historic TP sensor open/low 4.23 DTC P01 22, P0123
95 P0123 Historic TP sensor high 4.23 DTC P01 22, P0123
96 P0107 Historic MAP sensor open/low 4.20 DTC P01 07, P0108
97 P0108 Historic MAP sensor high 4.20 DTC P01 07, P0108
Коды Ошибок мотоциклов Harley-Davidson
The trip odometer trigger switch is located in the left hand control module.
The switch signal is sent to the speedometer over the CAN bus.
If there is a problem with the CAN bus, the odometer self-diagnostic mode maynot function.
For a quick check of instrument function, perform a «WOW» test by entering odometer self-diagnostics.
Background lighting will illuminate, gauge needles will sweep their full range of motion and all indicator lamps
controlled by the CAN circuit will illuminate.
If the instrument fails «WOW» test, check for battery power and ground to the instrument.
If any feature in the speedometer is non-functional, see Description and Operation.
Table 1. Diagnostic Trouble Codes (DTCs) and Fault Conditions
FAULT CONDITION SOLUTION
B1103 47 LHCM internal error
B1153 46 RHCM internal error
B1200 37 IM internal fault
B1210 176 Fuel level sender shorted low/open
B1211 182 Fuel level sender shorted high
B1212 175 Fuel signal low
B1213 176 Fuel signal high
B1300 340 Radio voltage high
B1301 341 Radio voltage low
B1302 342 Faceplate home button stuck
B1303 343 Faceplate favorite button stuck
B1304 344 Faceplate navigation button stuck
B1305 345 Faceplate power/mute button stuck
B1306 399 Rear hand controls shorted high
B1307 400 Rear hand controls shorted low
B1308 401 Rear volume up button stuck
B1309 402 Rear volume down button stuck
B1310 403 Rear mode button stuck
B1311 404 Rear PTT button stuck
B1312 405 Rear tune up button stuck
B1313 406 Rear tune down button stuck
B1314 346 LHCM VR PTT button stuck
B1315 347 LHCM up button stuck
B1316 348 LHCM left button stuck
B1317 349 LHCM center button stuck
B1318 350 LHCM right button stuck
B1319 351 LHCM down button stuck
B1320 352 RHCM info button stuck
B1321 353 RHCM up button stuck
B1322 354 RHCM left button stuck
B1323 355 RHCM center button stuck
B1324 356 RHCM right button stuck
B1325 357 RHCM down button stuck
B1326 358 RHCM CB squelch up button stuck
B1327 359 RHCM CB PTT button stuck
B1328 360 RHCM CB squelch down button stuck
B1329 361 Faceplate preset button 1 stuck
B1330 362 Faceplate preset button 2 stuck
B1331 363 Faceplate preset button 3 stuck
B1332 364 Faceplate preset button 4 stuck
B1333 365 Faceplate preset button 5 stuck
B1334 366 Faceplate preset button 6 stuck
B1335 367 Faceplate preset button 7 stuck
B1336 368 Faceplate preset button 8 stuck
B1337 369 Front left speaker shorted together
B1338 370 Front left speaker open
B1339 371 Front left speaker shorted low
B1340 372 Front left speaker shorted high
B1341 373 Rear left speaker shorted together
B1342 374 Rear left speaker open
B1343 375 Rear left speaker shorted low
B1344 376 Rear left speaker shorted high
B1345 377 Front right speaker shorted together
B1346 378 Front right speaker open
B1347 379 Front right speaker shorted low
B1348 380 Front right speaker shorted high
B1349 381 Rear right speaker shorted together
B1350 382 Rear right speaker open
B1351 383 Rear right speaker shorted low
B1352 384 Rear right speaker shorted high
B1353 385 Speaker output DC offset
B1354 386 GPS antenna open
B1355 387 GPS antenna shorted low
B1356 388 SDARS antenna open
B1357 389 SDARS antenna shorted
B1358 390 Front left headset shorted high
B1359 391 Front right headset shorted high
B1360 392 Front left headset shorted low
B1361 393 Front right headset shorted low
B1362 394 Rear left headset shorted high
B1363 395 Rear right headset shorted high
B1364 396 Rear left headset shorted low
B1365 397 Rear right headset shorted low
B1366 398 Internal thermal shutdown error
B1367 451 WIM fault detected Code used to support P&
B1401 407 Amp voltage low
B1402 408 Amp voltage high
B1403 409 Speaker output DC offset
B1404 410 Internal thermal shutdown error
B1405 427 EQ correlation error
B1406 428 Invalid or missing EQ
B1410 411 Channel 1 speaker open
B1411 412 Channel 1 speaker shorted low
B1412 413 Channel 1 speaker shorted high
B1413 414 Channel 1 speaker shorted together
B1420 415 Channel 2 speaker open
B1421 416 Channel 2 speaker shorted low
B1422 417 Channel 2 speaker shorted high
B1423 418 Channel 2 speaker shorted together
B1430 419 Channel 3 speaker open
B1431 420 Channel 3 speaker shorted low
B1432 421 Channel 3 speaker shorted high
B1433 422 Channel 3 speaker shorted together
B1440 423 Channel 4 speaker open
B1441 424 Channel 4 speaker shorted low
B1442 425 Channel 4 speaker shorted high
B1443 426 Channel 4 speaker shorted together
B2102 4 System power output shorted high
B2103 5 System power output shorted low
B2104 6 System power output overloaded
B2106 257 L4 output open
B2107 225 L4 output shorted high
B2108 226 L4 output shorted low
B2109 227 L4 output overloaded
B2112 132 ACC output shorted high
B2113 134 ACC output shorted low
B2114 136 ACC output overloaded
B2116 92 Fuel pump output open
B2117 93 Fuel pump output shorted high
B2118 94 Fuel pump output shorted low
B2119 95 Fuel pump output overloaded
B2121 58 Starter output open
B2122 59 Starter output shorted high
B2123 60 Starter output shorted low
B2124 61 Starter output overloaded
B2127 243 E4 output shorted high
B2128 244 E4 output shorted low
B2129 245 E4 output overloaded
B2131 233 High beam output open
B2132 234 High beam output shorted high
B2133 235 High beam output shorted low
B2134 236 High beam output overloaded
B2136 229 Low beam output open
B2137 230 Low beam output shorted high
B2138 231 Low beam output shorted low
B2139 232 Low beam output overloaded
B2141 207 Left front turn signal output open
B2143 214 Left front turn signal output shorted low
B2144 215 Left front turn signal output overloaded
B2146 216 Right front turn signal output open
B2148 217 Right front turn signal output shorted low
B2149 218 Right front turn signal output overloaded
B2151 219 Left rear turn signal output open
B2153 220 Left rear turn signal output shorted low
B2154 221 Left rear turn signal output overloaded
B2156 222 Right rear turn signal output open
B2158 223 Right rear turn signal output shorted low
B2159 224 Right rear turn signal output overloaded
B2161 198 Brake lamp output open
B2163 199 Brake lamp output shorted low
B2164 200 Brake lamp output overloaded
B2168 172 Running lights output shorted low
B2169 173 Running lights output overloaded
B2172 237 H2 output shorted high
B2173 238 H2 output shorted low
B2176 239 Security antenna output open
B2177 240 Security antenna output shorted high
B2178 241 Security antenna output shorted low
B2183 249 G2 output shorted low
B2188 254 G3 output shorted low
B2193 257 H4 output shorted low
B2198 259 H3 output shorted low
B2201 52 IGN switch off w/VSS
B2202 53 Ignition switch accy with vehicle speed
B2203 50 Ignition switch input shorted low
B2206 51 Run/stop switch input open/shorted high
B2208 54 Run/stop switch input shorted low
B2210 55 Run/stop switch inputs both open
B2212 56 Run/stop switch inputs both closed
B2218 131 Neutral switch shorted low
B2223 197 Rear brake switch shorted low (light on)
B2226 247 BAS input open BCM not configured properly.
B2228 250 BAS input shorted low BCM not configured properly.
B2231 312 Fork locked w/VSS BCM not configured properly. This DTC should
only apply to CVO models.
B2232 313 Fork lock shorted high BCM not configured properly. This DTC should
only apply to CVO models.
B2233 314 Fork lock shorted low BCM not configured properly. This DTC should
only apply to CVO models.
B2234 315 Fork lock detected w/option disabled
BCM not configured properly. This DTC should
only apply to CVO models.
B2235 316 Fork lock configuration invalid BCM not configured properly. This DTC should
only apply to CVO models.
B2250 128 Clutch switch stuck
B2251 242 Horn switch stuck
B2253 228 FTP switch stuck
B2254 203 Left turn switch stuck
B2255 246 Trip switch stuck
B2256 208 LHCM police siren power switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2257 209 LHCM police siren wail power switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2258 210 LHCM police siren yelp switch stuck BCM not configured properly. This DTC should
only apply to Police models.
B2260 57 Start switch stuck
B2261 204 Right turn switch stuck
B2262 196 Front brake switch stuck
B2263 202 Hazard switch stuck
B2264 211 RHCM police lights power switch BCM not configured properly. This DTC should stuck only apply to Police models.
B2265 212 RHCM police lights front switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2266 213 RHCM police lights rear switch stuck
BCM not configured properly. This DTC should
only apply to Police models.
B2270 27 BCM internal error
B2271 26 BCM voltage low
B2272 33 BCM/IM voltage high
B2274 49 Constant battery line error
C0562 38 ABS voltage low
C0563 40 ABS voltage high
C1014 183 ABS ECU relay error
C1021 191 ABS front WSS always zero
C1023 192 ABS rear WSS always zero
C1025 194 ABS front wheel speed intermittent
C1027 195 ABS rear wheel speed intermittent
C1029 193 ABS wheel speed difference too high
C1032 189 ABS front wheel speed circuit open/shorted
C1034 190 ABS rear wheel speed circuit open/shorted
C1040 184 ABS pump/motor error
C1055 39 ABS ECU internal error
C1061 185 ABS front apply solenoid circuit open/high resistance
C1062 187 ABS front release solenoid circuit open/high resistance
C1065 186 ABS rear apply solenoid circuit open/high resistance
C1066 188 ABS rear release solenoid circuit open/high resistance
C1071 283 Rear prime valve error
C1072 284 Rear isolation valve error
C1073 285 Front isolation valve error
C1074 286 Front prime valve error
C1075 287 Front linked inlet valve error
C1076 288 Front linked outlet valve error
C1077 289 Front circuit pressure sensor error
C1078 290 Rear circuit pressure sensor error
C1081 291 Front master pressure sensor error
C1082 292 Front master pressure sensor offset error
C1083 293 Front wheel pressure sensor error
C1084 294 Front wheel pressure sensor offset error
C1085 295 Rear master pressure sensor error
C1086 296 Rear master pressure sensor offset error
C1087 297 Rear wheel pressure sensor error
C1088 298 Rear wheel pressure sensor offset error
C1089 299 Pressure sensor external supply error
C1159 43 ABS invalid stored VIN
C1178 41 ABS no VIN received from ECM
C1184 42 ABS invalid VIN from ECM
C1195 266 Wake up error
P0031 153 Front HO2S low/open
P0032 156 Front HO2S shorted high
P0051 154 Rear HO2S low/open
P0052 155 Rear HO2S shorted high
P0072 112 AAT sensor low
P0073 113 AAT sensor high/open
P0107 100 MAP sensor failed low/open
P0108 101 MAP sensor failed high/open port
P0112 123 IAT sensor shorted low
P0113 125 IAT sensor high/open
P0117 102 ET sensor shorted low
P0118 107 ET sensor high/open
P0120 76 TPS 1 range error
P0122 74 TPS 1 low
P0123 75 TPS 1 high/open
P0131 157 O2 sensor low/engine lean (front)
P0132 159 Engine running rich (front)
P0134 161 Oxygen sensor high/open (front)
P0151 158 O2 sensor low/engine lean (rear)
P0152 160 Engine running rich (rear)
P0154 162 O2 sensor high/open (rear)
P0220 79 TPS 2 range error
P0222 77 TPS 2 low/open
P0223 78 TPS 2 high
P0261 96 Fuel injector low/open (front)
P0262 97 Fuel injector shorted high (front)
P0264 98 Fuel injector low/open (rear)
P0265 99 Fuel injector shorted high (rear)
P0325 139 Knock sensor front open circuit
P0327 140 Knock sensor front circuit low
P0328 141 Knock sensor front circuit high
P0330 142 Knock sensor rear open circuit
P0332 143 Knock sensor rear circuit low
P0333 144 Knock sensor rear circuit high
P0371 65 CKP sensor wrong number of Description and Operation pulses
P0374 64 CKP sensor no pulses
P0444 147 Purge solenoid low/open
P0445 148 Purge solenoid shorted high
P0462 174 Fuel sender shorted low
P0463 175 Fuel sender shorted high/open
P0502 137 VSS failed low
P0503 138 VSS failed high
P0522 168 Engine oil pressure sensor/switchм shorted low
P0523 169 Engine oil pressure sensor/switch shorted high/open
P0562 127 ECM voltage low
P0572 202 Brake switch low
P0577 163 Cruise control input error
P0603 29 ECM EEPROM memory error
P0605 28 ECM FLASH memory error
P0641 62 5 Volt reference out of range
P0651 63 5 Volt reference 2 out of range
P0693 119 Chassis fan control circuit shorted low
P0694 120 Chassis fan control circuit shorted high
P1009 32 VTD disabled fuel due to bad password
P1017 103 ET indicates overheating
P1019 106 ECT difference (high temp)
P1270 67 TGS 2 A/D validation error
P1502 167 JSS high/open
P1505 445 Power limit violation
P1510 447 ETC limited performance mode
P1511 448 ETC power management mode
P1512 449 ETC forced idle mode
P1514 87 ETC airflow error
P1600 66 ETC watchdog error
P1655 164 ACR solenoid low/open
P1656 165 ACR solenoid shorted high
P1691 115 Cooling fan left low/open
P1692 116 Cooling fan left shorted high
P1693 117 Cooling fan right low/open
P1694 118 Cooling fan right shorted high
P2100 82 ETC driver open circuit
P2101 83 ETC actuation error
P2102 84 ETC driver shorted low
P2103 85 ETC driver shorted high
P2105 446 ETC forced shutdown mode
P2107 68 ETC driver internal error
P2119 81 ETC actuator return error
P2122 69 TGS 1 low/open
P2123 70 TGS 1 high
P2127 71 TGS 2 low/open
P2128 72 TGS 2 high
P2135 80 TPS correlation error
P2138 73 TGS correlation error
P2176 86 ETC zero position learning error
P2184 121 ECT sensor low
P2185 122 ECT sensor high
P2300 88 Ignition coil driver low/open (front)
P2301 89 Ignition coil driver shorted high (front)
P2303 90 Ignition coil driver low/open (rear)
P2304 91 Ignition coil driver shorted high (rear)
P2602 104 Coolant pump «A» control circuit low
P2603 105 Coolant pump «A» control circuit high
U0001 1 CAN BUS error
U0002 16 CAN comm bus perf error
U0003 13 Network management monitoring
U0011 2 CAN bus low shorted to CAN bus high
U0100 7 Lost comm w/ECM
U0121 11 Lost comm w/ABS
U0140 3 Lost comm w/BCM
U0141 9 Lost comm w/LHCM
U0142 8 Lost comm w/RHCM
U0156 10 Lost comm w/speedo
U0158 180 Lost comm w/fuel gauge
U0159 181 Lost comm w/volt gauge
U0160 179 Lost comm w/fuel and volt gauges
U0184 323 Lost comm w/radio
U0185 325 Lost comm w/AMP 1
U0186 326 Lost comm w/AMP 2
U0300 15 Internal control module software incompatibility
U1302 324 ACC bus perf error
U1401 331 Lost comm w/CB
U1401 331 Lost comm w/CB
U1405 450 ACC bus lost comm w/ WIM Code used to support P&A parts